Quirce
06-08-2009, 12:50 AM
A SIMPLE EXPERIMENT, A NAÏVE EXPLANATION.
More than a century ago, Hertz created and detected electromagnetic waves with his famous experiment.
We wanted to repeat the experiment home , using as an instrument for creating E.M, waves : a common micro waves oven. For resonator we used an iron sheet (thick foil), cut in it a round piece 2 cm radius, make a hole in center about 5 mm. and cut a radial slit with a gap I mm. near center and 3 mm. in periphery. For supporting the resonator, we soldered it on a thick 2 mm copper wire, and put the supporter in a cup of water.
The resonator, inside of the chamber of microwave oven, faced the conductor of E.M. waves.
We put the time 50 sec. and start the oven. After a while in the gap of slit began electric arch with a white light, very shiny, like a little torch, with characteristic sound of electric arch. It lasted all the set time. We repeated the process several times with the same result.
A resonator without a slit did not performed arch.
I- This is the fact. It is evident that some of energy from electromagnetic microwaves with a frequency of about 2.4*10^9 hz. was transformed in this experiment in electromagnetic waves with a frequency in the band of visible light ( about 3*10^14 hz.), that is in photons with higher energy, via Eh = h*f. I wonder: what is the rapport between the number of the photons input with the number of photons output? Is it here room for free lunch? Ha?
II- If we can augmenting the activity of the electric arch, in somehow manner, will it retroactive with magnetron activity, similarly the short-cut in electric circuits? I think not because the photons emitted by magnetron becomes independent from the source. Am I right?
III-About the mechanism of transformation OF ONE KIND OF PHOTON IN OTHER KIND, in this experiment, some people gave a simple explanation: the E.M. wave from the magnetron push the electrons of the metallic plate (resonator), in the sharpest its regions, augmenting the intensity of static electric field, that is the electric tension. There began the corona discharge, which is something different from electric arch. It has to do with electrons in the periphery of oxygen and nitrogen atoms of the air. They absorbs and emits the photons of different frequencies.
-- But if not an electric arch, why the lips of slit are melted?
--------------- ---------------
The naïve explanation.
Photon consist by two unique particles: - e / - (G)^0.5 = M1 and
+ e / + (G)*0.5 = M2 which evolve toward each other with c velocity, in a distance “ rx “ . The distance determines the frequency of the photon. The summa of electric charges and gravity charges is zero, so the total charge and total mass of photon is zero.
Electron particle consist by two the same unique particles: M1
which evolve toward each other in a stationary status with C velocity in a radius equal classic radius of electron particle.
Positron particle consist by two the same unique particles: M2
When electron is forced to jump over cavity from one anode to other which are apart in a distance “ rx “, the electron split in the two constituents, simultaneously the positron (from the Dirac sea?) jumps in opposite direction and split too in two own constituents. In the distance “ rx “ the constituent M1 of electron find the new partner M2 from positron and binds himself in a new connection : M1 , rx , M2 that is in the status of photon particle, where the distance “ rx “ determine the frequency of photon.
On the other hand when a wave particle hit a metallic lip it slips in its constituents, and they reconnected themselves in a new radius, giving a photon with different frequency.
So the gap between two anodes in oven’s magnetron, or between two lips of slit in resonator have to do directly what will be the frequency of photon.
More than a century ago, Hertz created and detected electromagnetic waves with his famous experiment.
We wanted to repeat the experiment home , using as an instrument for creating E.M, waves : a common micro waves oven. For resonator we used an iron sheet (thick foil), cut in it a round piece 2 cm radius, make a hole in center about 5 mm. and cut a radial slit with a gap I mm. near center and 3 mm. in periphery. For supporting the resonator, we soldered it on a thick 2 mm copper wire, and put the supporter in a cup of water.
The resonator, inside of the chamber of microwave oven, faced the conductor of E.M. waves.
We put the time 50 sec. and start the oven. After a while in the gap of slit began electric arch with a white light, very shiny, like a little torch, with characteristic sound of electric arch. It lasted all the set time. We repeated the process several times with the same result.
A resonator without a slit did not performed arch.
I- This is the fact. It is evident that some of energy from electromagnetic microwaves with a frequency of about 2.4*10^9 hz. was transformed in this experiment in electromagnetic waves with a frequency in the band of visible light ( about 3*10^14 hz.), that is in photons with higher energy, via Eh = h*f. I wonder: what is the rapport between the number of the photons input with the number of photons output? Is it here room for free lunch? Ha?
II- If we can augmenting the activity of the electric arch, in somehow manner, will it retroactive with magnetron activity, similarly the short-cut in electric circuits? I think not because the photons emitted by magnetron becomes independent from the source. Am I right?
III-About the mechanism of transformation OF ONE KIND OF PHOTON IN OTHER KIND, in this experiment, some people gave a simple explanation: the E.M. wave from the magnetron push the electrons of the metallic plate (resonator), in the sharpest its regions, augmenting the intensity of static electric field, that is the electric tension. There began the corona discharge, which is something different from electric arch. It has to do with electrons in the periphery of oxygen and nitrogen atoms of the air. They absorbs and emits the photons of different frequencies.
-- But if not an electric arch, why the lips of slit are melted?
--------------- ---------------
The naïve explanation.
Photon consist by two unique particles: - e / - (G)^0.5 = M1 and
+ e / + (G)*0.5 = M2 which evolve toward each other with c velocity, in a distance “ rx “ . The distance determines the frequency of the photon. The summa of electric charges and gravity charges is zero, so the total charge and total mass of photon is zero.
Electron particle consist by two the same unique particles: M1
which evolve toward each other in a stationary status with C velocity in a radius equal classic radius of electron particle.
Positron particle consist by two the same unique particles: M2
When electron is forced to jump over cavity from one anode to other which are apart in a distance “ rx “, the electron split in the two constituents, simultaneously the positron (from the Dirac sea?) jumps in opposite direction and split too in two own constituents. In the distance “ rx “ the constituent M1 of electron find the new partner M2 from positron and binds himself in a new connection : M1 , rx , M2 that is in the status of photon particle, where the distance “ rx “ determine the frequency of photon.
On the other hand when a wave particle hit a metallic lip it slips in its constituents, and they reconnected themselves in a new radius, giving a photon with different frequency.
So the gap between two anodes in oven’s magnetron, or between two lips of slit in resonator have to do directly what will be the frequency of photon.